Internet Computer Mobile Games

A common basic trunk/tag setup

Can someone show me in full the needed code to trunk a switch. I'm having trouble with trunks in my srx240's . This is srx240 to Avaya or baystack . The code for the trunk tag requirements only. Not the rest of the config. My trunks do not seem to pass any traffic. I live in a hostile environment, is my guess, but I'm green on the SRX too.

Vlan 1 and vlan 2 is the need...

Preferrably with a full vlan2. Secondary would be setting an address at the interface in question but both examples is fine.

Top similar posts to A common basic trunk/tag setup

Basic Router to Internet Setup for Dell PowerConnect 6248p

I would like to preface this by saying that I am extremely new to any kind of in-depth networking. For a project, I am attempting to set up a Dell PowerConnect 6248p switch as a basic "router multiplexer" if you will. My current goal is to connect several servers and a router to the switch and have the router handle DHCP and give the devices access to the internet. I am well aware that the PowerConnect 6200 series is OSI Layer 3-Capable; however, I would like to set it up in this basic manner ...

AIO system setup collection of basic info

Folks: Hoping someone can help with this.  We have a Lenovo AIO C40-05 and the original harddrive crashed. We were able to have a local repair shop replace the hard drive and get us up and running again.  Unfortunately we can't get rid the pop up shown below. I've gone into the restart options but can't find anywhere to disable this.   Many thanksDerek    ...

Cisco Switch basic setup for a simple private lan

I have a 'private' lan. There is a 10-port Cisco SG300-10 switch, with 5 laptops connected to it. No internet is desired & no routers are present. Each laptop should be able to ping the other 4. Preferably the 5 laptops have static addresses (192.168.1.2,3,4,5 is good enough) Management console (192.168.1.254) works fine, and so does ssh. Since I am new to the world of switches, here are my questions/assumptions : 1) How do I associate a Mac address with an IP address in the 192.168.1.x r...

5 player warp zone map setup with six player basic setup

by shieldwolf I'm playing at 5 player game tomorrow with a lot of new players as such I want to use the 5 player warp setup so everyone is evenish. We're not going to be building a map so can I use the preset for the six player game? Or is there better alternate preset for a 5 player game...

ITT: basic things you dont know or care about that are common knowledge

i dont remember what a verb or noun is, only what adjectives are...

Basic universal forwarder setup with splunk enterprise

I am rolling out a trial instance of splunk enterprise, I have it running on a 2012r2 vm, and have installed the Universal Forwarder on two workstations pointing at it. My trouble is that I do not receive any data from the workstations. I have gone over the install/troubleshooting documentation several times but I feel like I'm missing something obvious, as the documentation seems to just assume that once you install the forwarder it should just work. Do I need to make config changes on the ser...

Basic bottom fishing setup, Fishing

Hey there I'm looking at trying to get out of tillamook bay and do some bottom fishing for bass and lings but I'm not sure where to start? Will salmon gear work as far as the rod and reel go? What type of lures do I need and just a basic setup will help. Thanks in advance...

Really basic SG300 VLAN setup not working

My understanding of VLANs may need improved, but isn't the idea that you can run multiple LANs at layer 2 level over the same router if VLANs are setup correctly on the SG300? If so, I fail to see how that can be enabled for my incredibly trivial use case: I have two separate LANs with separate DHCP servers (and separate IP ranges). To simplify my hardware setup, I've purchased an SG300 router, thinking I can assign each port on that router to be part of one or several VLANs (just one in my ca...

Basic drift setup

Hello everybody! I am from Sydney looking to buy a e36 or e46 (years 95'/00') as a drift project. Since i am complete noob with drifting, I am not the sure about the right engine size I need and if I will be able to drift it bare stock or I need some basic setup? I tried to search here for a basic setup and couldn't find, links with info of basic setup will be much appreciated. Cheers!...

WTS: WTS Onkyo HTS-3800 5 yr Warranty | With basic setup and delivery

Want to sell off Onkyo HTS-3800. HT-S3800 | ONKYO Asia and Oceania Website *Take note speaker can be upgraded but not the subwoofer. This HTS system supports 4K HDR passthrough, very good surround sound experience better than soundbar. I will provide: - Basic setup Connecting AMP to TV, Connecting speaker wire, calibration and etc. For wall mount and etc. it will be quote by vendor so I don't do that. *It can be time consuming especially the sound calibration. Additional Speaker ...

WTS Onkyo HTS-3800 5 yr Warranty | With basic setup and delivery

Want to sell off Onkyo HTS-3800. http://www.intl.onkyo.com/products/s...800/index.html *Take note speaker can be upgraded but not the subwoofer. This HTS system supports 4K HDR passthrough, very good surround sound experience better than soundbar. I will provide: - Basic setup Connecting AMP to TV, Connecting speaker wire, calibration and etc. For wall mount and etc. it will be quote by vendor so I don't do that. *It can be time consuming especially the sound calibration. Additio...

Adding Event Cards to Basic Common Cards

by greenbeehive I know the typical rules for adding in expansions and common cards. Is there any reason to add the Event cards from other expansions to any or all games? I can't see a reason but others may have one....

C++: Setup the basic Update function in different classes which all derive from GameObject

Im working on a little game-framework in c++. Currently i have a (base)class called "GameObject" from which all future in-game objects will derive from. Class enemy will be class Enemy : public GameObject and class Player will be class Player : public GameObject This way, i can store all my gameobjects in an array of type GameObject and manage them easily and they will all have the basic game-object variables such as x/y/z coordinates, scale, etc. So what i eventually want is to be able to quic...

How to setup basic multicast connectivity from source to receiver connected over the same router

Hi All,   Kindly help me on this. I have Video source and one few receivers connected to the same MX on two different interfaces. i am specifically testing for multicast connectivity. after looking up some resources, it looked to me that i need to enable PIM and add the two interfaces under it.    Am totaly new to the multicast and need basic guide lines on the following: Source and recievers connected to the same router, how will the multicast setup look like? do the source and ...

Looking for under $1k receiver that suits my odd/basic setup

I'm looking for a new receiver for my setup and wondering if there are any options I'm not considering, or if there's some other way of setting up my system I'm not considering. My main use of the receiver is as a HDMI matrix switch, so Zone 2 is an absolute must. My wife and I game in the same room and like to have the ability to switch our systems to either TV without any fuss. The main TV is the one with the surround sound setup, and the smaller TV works as-is with the TV speakers. I curren...

Design Apple Development Security Automobile Network Photography Health Money Travel Shopping Issues Operating systems Drivers Software Programming Tech Home Science Sport Solution